on_wifi_callback() descryption and loop in wrong setup for AP connection

terefere

Firs matter: can you provide some decryption for value who give this routine?

Second: When I set incorrect data for connection to router then I see that wifi module try to force connection in loop- not finish procedure after show error. I don't think so, that is good. It look's like below. Is any solution ?, at now I try kill it by connect with empty SSID string. At line 234 is my code, here I also I try to call reset_ethernet() but I get error for nil value- must be something inside this routine?

1. start_connect_wifi
   
2. [WIFIMGR] START to Connect!
   
3. netlinkbuffer.setflags = 22, cmd: 0x8B15
   
4. netlinkbuffer.recvflags = 22
   
5. netlink: 52 extra bytes in the end of netlink message
   
6. ioctl[SIOCSIWAP]: Success
   
7. [WIFIMGR] ssid     = XFF
   
8. [WIFIMGR] password = iut
   
9. [WIFIMGR] secumode = 6
   
10. add_network = 0
    
11. 
    
12. WLAN_SEC_WPAPSK_MIX
    
13. Line 0: Invalid passphrase length 3 (expected: 8..63) 'iut"'.
    
14. [WIFIMGR] Wait for connecting
    
15. ....netlinkbuffer.setflags = 23, cmd: 0x8B19
    
16. netlinkbuffer.recvflags = 23
    
17. netlink: 52 extra bytes in the end of netlink message
    
18. .netlinkbuffer.setflags = 0, cmd: 0x8B15
    
19. netlinkbuffer.recvflags = 0
    
20. netlink: 52 extra bytes in the end of netlink message
    
21. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
    
22.      ==> rssi_level:0, rate_bitmap:0x000ff015
    
23. IEEE 802.1X RX: version=2 type=3 length=117
    
24. RSN: no matching PMKID found
    
25. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
26. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
    
27.      ==> rssi_level:1, rate_bitmap:0x000f0000
    
28. RSN: no matching PMKID found
    
29. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
30. RSN: no matching PMKID found
    
31. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
32. RSN: no matching PMKID found
    
33. .......HEAP newlib: usage=39360120/51766752(76%),addr=0xA6F220
    
34. ..IEEE 802.1X RX: version=2 type=3 length=117
    
35. RSN: no matching PMKID found
    
36. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
37. RSN: no matching PMKID found
    
38. .........IEEE 802.1X RX: version=2 type=3 length=117
    
39. RSN: no matching PMKID found
    
40. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
41. RSN: no matching PMKID found
    
42. ..........netlinkbuffer.setflags = 1, cmd: 0x8B15
    
43. netlinkbuffer.recvflags = 1
    
44. netlink: 52 extra bytes in the end of netlink message
    
45. .........netlinkbuffer.setflags = 2, cmd: 0x8B19
    
46. netlinkbuffer.recvflags = 2
    
47. netlink: 52 extra bytes in the end of netlink message
    
48. .netlinkbuffer.setflags = 3, cmd: 0x8B15
    
49. netlinkbuffer.recvflags = 3
    
50. netlink: 52 extra bytes in the end of netlink message
    
51. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
    
52.      ==> rssi_level:0, rate_bitmap:0x000ff015
    
53. IEEE 802.1X RX: version=2 type=3 length=117
    
54. RSN: no matching PMKID found
    
55. ..UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
    
56.      ==> rssi_level:1, rate_bitmap:0x000f0000
    
57. ........IEEE 802.1X RX: version=2 type=3 length=117
    
58. RSN: no matching PMKID found
    
59. .........IEEE 802.1X RX: version=2 type=3 length=117
    
60. RSN: no matching PMKID found
    
61. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
62. RSN: no matching PMKID found
    
63. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
64. RSN: no matching PMKID found
    
65. .........HEAP newlib: usage=39360504/51766752(76%),addr=0xA6F220
    
66. IEEE 802.1X RX: version=2 type=3 length=117
    
67. RSN: no matching PMKID found
    
68. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
69. RSN: no matching PMKID found
    
70. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
71. RSN: no matching PMKID found
    
72. .........netlinkbuffer.setflags = 4, cmd: 0x8B15
    
73. netlinkbuffer.recvflags = 4
    
74. netlink: 52 extra bytes in the end of netlink message
    
75. ....netlinkbuffer.setflags = 5, cmd: 0x8B19
    
76. netlinkbuffer.recvflags = 5
    
77. netlink: 52 extra bytes in the end of netlink message
    
78. .netlinkbuffer.setflags = 6, cmd: 0x8B15
    
79. netlinkbuffer.recvflags = 6
    
80. netlink: 52 extra bytes in the end of netlink message
    
81. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
    
82.      ==> rssi_level:0, rate_bitmap:0x000ff015
    
83. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
    
84.      ==> rssi_level:3, rate_bitmap:0x000ff015
    
85. IEEE 802.1X RX: version=2 type=3 length=117
    
86. RSN: no matching PMKID found
    
87. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
88. RSN: no matching PMKID found
    
89. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
90. RSN: no matching PMKID found
    
91. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
    
92.      ==> rssi_level:1, rate_bitmap:0x000f0000
    
93. .........IEEE 802.1X RX: version=2 type=3 length=117
    
94. RSN: no matching PMKID found
    
95. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
96. RSN: no matching PMKID found
    
97. .........IEEE 802.1X RX: version=2 type=3 length=117
    
98. RSN: no matching PMKID found
    
99. ..........IEEE 802.1X RX: version=2 type=3 length=117
    
100. RSN: no matching PMKID found
     
101. ........HEAP newlib: usage=39376472/51766752(76%),addr=0xA6F220
     
102. ..IEEE 802.1X RX: version=2 type=3 length=117
     
103. RSN: no matching PMKID found
     
104. .........netlinkbuffer.setflags = 7, cmd: 0x8B15
     
105. netlinkbuffer.recvflags = 7
     
106. netlink: 52 extra bytes in the end of netlink message
     
107. .....get_stat!
     
108. .....netlinkbuffer.setflags = 8, cmd: 0x8B19
     
109. netlinkbuffer.recvflags = 8
     
110. netlink: 52 extra bytes in the end of netlink message
     
111. netlinkbuffer.setflags = 9, cmd: 0x8B15
     
112. netlinkbuffer.recvflags = 9
     
113. netlink: 52 extra bytes in the end of netlink message
     
114. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
     
115.      ==> rssi_level:0, rate_bitmap:0x000ff015
     
116. IEEE 802.1X RX: version=2 type=3 length=117
     
117. RSN: no matching PMKID found
     
118. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
119. RSN: no matching PMKID found
     
120. ...UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
     
121.      ==> rssi_level:1, rate_bitmap:0x000f0000
     
122. .......IEEE 802.1X RX: version=2 type=3 length=117
     
123. RSN: no matching PMKID found
     
124. .........IEEE 802.1X RX: version=2 type=3 length=117
     
125. RSN: no matching PMKID found
     
126. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
127. RSN: no matching PMKID found
     
128. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
129. RSN: no matching PMKID found
     
130. .........IEEE 802.1X RX: version=2 type=3 length=117
     
131. RSN: no matching PMKID found
     
132. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
133. RSN: no matching PMKID found
     
134. .........netlinkbuffer.setflags = 10, cmd: 0x8B15
     
135. netlinkbuffer.recvflags = 10
     
136. netlink: 52 extra bytes in the end of netlink message
     
137. ..HEAP newlib: usage=39377048/51766752(76%),addr=0xA6F220
     
138. .........netlinkbuffer.setflags = 11, cmd: 0x8B19
     
139. netlinkbuffer.recvflags = 11
     
140. netlink: 52 extra bytes in the end of netlink message
     
141. netlinkbuffer.setflags = 12, cmd: 0x8B15
     
142. netlinkbuffer.recvflags = 12
     
143. netlink: 52 extra bytes in the end of netlink message
     
144. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
     
145.      ==> rssi_level:0, rate_bitmap:0x000ff015
     
146. IEEE 802.1X RX: version=2 type=3 length=117
     
147. RSN: no matching PMKID found
     
148. .....UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
     
149.      ==> rssi_level:1, rate_bitmap:0x000f0000
     
150. .....IEEE 802.1X RX: version=2 type=3 length=117
     
151. RSN: no matching PMKID found
     
152. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
153. RSN: no matching PMKID found
     
154. .........IEEE 802.1X RX: version=2 type=3 length=117
     
155. RSN: no matching PMKID found
     
156. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
157. RSN: no matching PMKID found
     
158. .........IEEE 802.1X RX: version=2 type=3 length=117
     
159. RSN: no matching PMKID found
     
160. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
161. RSN: no matching PMKID found
     
162. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
163. RSN: no matching PMKID found
     
164. .........netlinkbuffer.setflags = 13, cmd: 0x8B15
     
165. netlinkbuffer.recvflags = 13
     
166. netlink: 52 extra bytes in the end of netlink message
     
167. ....netlinkbuffer.setflags = 14, cmd: 0x8B19
     
168. netlinkbuffer.recvflags = 14
     
169. netlink: 52 extra bytes in the end of netlink message
     
170. .netlinkbuffer.setflags = 15, cmd: 0x8B15
     
171. netlinkbuffer.recvflags = 15
     
172. netlink: 52 extra bytes in the end of netlink message
     
173. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
     
174.      ==> rssi_level:0, rate_bitmap:0x000ff015
     
175. IEEE 802.1X RX: version=2 type=3 length=117
     
176. RSN: no matching PMKID found
     
177. ..UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
     
178.      ==> rssi_level:1, rate_bitmap:0x000f0000
     
179. .......HEAP newlib: usage=39376248/51766752(76%),addr=0xA6F220
     
180. .IEEE 802.1X RX: version=2 type=3 length=117
     
181. RSN: no matching PMKID found
     
182. .........IEEE 802.1X RX: version=2 type=3 length=117
     
183. RSN: no matching PMKID found
     
184. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
185. RSN: no matching PMKID found
     
186. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
187. RSN: no matching PMKID found
     
188. .........IEEE 802.1X RX: version=2 type=3 length=117
     
189. RSN: no matching PMKID found
     
190. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
191. RSN: no matching PMKID found
     
192. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
193. RSN: no matching PMKID found
     
194. .........netlinkbuffer.setflags = 16, cmd: 0x8B15
     
195. netlinkbuffer.recvflags = 16
     
196. netlink: 52 extra bytes in the end of netlink message
     
197. ...........netlinkbuffer.setflags = 17, cmd: 0x8B19
     
198. netlinkbuffer.recvflags = 17
     
199. netlink: 52 extra bytes in the end of netlink message
     
200. netlinkbuffer.setflags = 18, cmd: 0x8B15
     
201. netlinkbuffer.recvflags = 18
     
202. netlink: 52 extra bytes in the end of netlink message
     
203. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
     
204.      ==> rssi_level:0, rate_bitmap:0x000ff015
     
205. .IEEE 802.1X RX: version=2 type=3 length=117
     
206. RSN: no matching PMKID found
     
207. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
208. RSN: no matching PMKID found
     
209. ...UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
     
210.      ==> rssi_level:1, rate_bitmap:0x000f0000
     
211. ......IEEE 802.1X RX: version=2 type=3 length=117
     
212. RSN: no matching PMKID found
     
213. .HEAP newlib: usage=39376632/51766752(76%),addr=0xA6F220
     
214. .........IEEE 802.1X RX: version=2 type=3 length=117
     
215. RSN: no matching PMKID found
     
216. .........IEEE 802.1X RX: version=2 type=3 length=117
     
217. RSN: no matching PMKID found
     
218. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
219. RSN: no matching PMKID found
     
220. ..........IEEE 802.1X RX: version=2 type=3 length=117
     
221. RSN: no matching PMKID found
     
222. .........IEEE 802.1X RX: version=2 type=3 length=117
     
223. RSN: no matching PMKID found
     
224. ..........netlinkbuffer.setflags = 19, cmd: 0x8B15
     
225. netlinkbuffer.recvflags = 19
     
226. netlink: 52 extra bytes in the end of netlink message
     
227. ..
     
228. [WIFIMGR]WifiMgr_Connect() L#746: Timeout! Cannot connect to XFF!
     
229. [WIFIMGR]WifiMgr_Connect() L#780: Error! Cannot connect to WiFi AP!
     
230. [Indoor]WifiCallback connecting fail, please check ssid,password,secmode
     
231. deauth_reason_code(15)
     
232. [WIFIMGR] Connect finish!
     
233. on_wifi_callback(4,15)
     
234. ********** WiFi Callback **********
     
235. State: 4
     
236. Reason: 15
     
237. ********** ************* **********
     
238. ****************** Reset Ethernet ****************
     
239. error [string "------------------------------------
     
240. ..."]:885: attempt to call a nil value (global 'reset_ethernet')
     
241. [WIFIMGR]WiFiMgrProcessThreadFunc() L#1248: Error! nWiFiConnEcode = 010
     
242. netlinkbuffer.setflags = 20, cmd: 0x8B19
     
243. netlinkbuffer.recvflags = 20
     
244. netlink: 52 extra bytes in the end of netlink message
     
245. netlinkbuffer.setflags = 21, cmd: 0x8B15
     
246. netlinkbuffer.recvflags = 21
     
247. netlink: 52 extra bytes in the end of netlink message
     
248. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
     
249.      ==> rssi_level:0, rate_bitmap:0x000ff015
     
250. IEEE 802.1X RX: version=2 type=3 length=117
     
251. RSN: no matching PMKID found
     
252. IEEE 802.1X RX: version=2 type=3 length=117
     
253. RSN: no matching PMKID found
     
254. UpdateHalRAMask8188EUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
     
255.      ==> rssi_level:1, rate_bitmap:0x000f0000
     
256. IEEE 802.1X RX: version=2 type=3 length=117
     
257. RSN: no matching PMKID found
     
258. IEEE 802.1X RX: version=2 type=3 length=117
     
259. RSN: no matching PMKID found
     
260. HEAP newlib: usage=39391640/51766752(76%),addr=0xA6F220
     
261. IEEE 802.1X RX: version=2 type=3 length=117
     
262. RSN: no matching PMKID found
     
263. IEEE 802.1X RX: version=2 type=3 length=117
     
264. RSN: no matching PMKID found
     
265. IEEE 802.1X RX: version=2 type=3 length=117
     
266. RSN: no matching PMKID found
     
267. IEEE 802.1X RX: version=2 type=3 length=117
     
268. RSN: no matching PMKID found
     
269. netlinkbuffer.setflags = 22, cmd: 0x8B15
     
270. netlinkbuffer.recvflags = 22
     
271. netlink: 52 extra bytes in the end of netlink message
     
272. netlinkbuffer.setflags = 23, cmd: 0x8B19
     
273. netlinkbuffer.recvflags = 23
     
274. netlink: 52 extra bytes in the end of netlink message
     
275. netlinkbuffer.setflags = 0, cmd: 0x8B15
     
276. netlinkbuffer.recvflags = 0

复制代码

If后要接end

1: Do you mean lua for each statement explaination in this routine?

2:call reset_ethernet() get error, you can make sure the firmware version number of the screen. Place a text widget in the screen,  the text widget properties to system variables, and download the project to the screen for viewing

terefere

1. I mean what interesting for me can say "state and reason"
2. Bit not clear for me, U want to know my screen version?

If后要接end

1、When the screen is not connected to the Internet normally, the wifi status displayed in the Debug message may not be correct, depending on the wifi error message, for example at line 230
2、yep，Older firmware versions cannot use reset_ethernet()